Products

• 24 calibrated ranges
• isolation unipolar and bipolar signals
• setting ranges by slid switches DIP on the board
• digital processing and transfer A/D and D/A
• response time: 1ms, adjustable to 100ms by switch
• accuracy 0,1%
• power supply 18VDC for loop-powered transmitter on input
• dielectric strength input / output & supply power 4kV
• auxiliary power supply 24VDC ± 25%

• two-channel converter PP210_Tc without galvanic isolation
• it converts temperature from any thermocouple to 4..20mA
• cold junction compensation
• easy programming by AX-USB adapter (AY-USB) without power supply
• each channel can be set independently
• power supply by output loop 8…30V DC, any polarity
• DIN 35 rail-mounted design

• pH range: 0..13
• working temperature 0..+70°C
• zero point: pH = 7
• max. pressure: 3 bar
• various sizes

• with auxiliary power supply
• transducer for measurement DC current or voltage
• allows unipolar and bipolar input and output signal
• directly current measurements up to ±10A DC, voltage up to ±1500V DC
• ability to measure absolute values and inverted signal
• conversion accuracy <0,1%
• response time 1ms, for order up to 300ms
• dielectric strength input / output / supply power 5kVrms
• universal power supply 16 – 300V DC & 90 – 250V AC
• rated impuls voltage  Uni: 8kV
• clearances and creepage distances min. 8mm
• designed for DIN 35 rail mounting

• basic design: 6x50mm Pt100/B with cable 4w 1m
• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• temperature range -30…+80°C with cable PVC IP68 (T=c. 7sec)
• dielectric strength: 500V, insulation resistance min. 20MΩ (circuit to metal parts)

• analog measurement of the input signal
• transducer for measurement DC current or voltage
• allows unipolar and bipolar input and output signal
• directly current measurements up to ±10A, voltage up to ±1000V DC
• conversion accuracy <0,1%
• response time 1ms
• dielectric strength input / output / supply power 4kV
• universal power supply 19 – 300V DC & 90 – 250V AC

• two-state programmable switch for monitoring of electrical values or temperature
• output relay with changeover contact
• Possibility of easy setting of switching value by potentiometer or programmed
• input only RTD, R
• supply voltage: 12V / 24V DC ± 25% without galvanic isolation
• DIN rail mounting
• the temperature adjusting element is inside the housing

• analog measurement
• true RMS value of current or voltage
• signal processing with crest factor up 10
• frequency range 40 … 1000Hz
• conversion accuracy  0,5%
• response time 300ms
• isolation input-output-power supply: 4000Vef
• loop-powered

• transmitter is mounted in a connection head DIN "MAA" dimension or any box
• easy programming by AX-USB adapter (AY-USB) without power supply
• it converts temperature from RTD thermometer to 4..20mA
• transmitter can be set for sensors Pt100/Ni100 or Pt1000/Ni1000

• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• for outdoor use, IP65, -50…+100°C

• converter without galvanic isolation
• transmitter with 4-20mA otput is designed for transduction:
     - voltage from any thermocouple with linearization and cold junction compensation
     - temperature from RTD or resistance from resistance transmitter
• easy programming by AX-USB adapter (AY-USB) without power supply
• power supply by output loop 11…30V DC, any polarity
• slim design, DIN 35 rail-mounted, width 12,5mm

• 4-20mA loop-powered
• rated impuls voltage Uni: 8kV
• analog measurement of the input signal
• transducer for measurement RMS value of AC current or voltage
• signal processing  with crest factor of 10
• frequency range 40 až 1000Hz
• accuracy <0,5%
• response time 300ms
• dielectric strenght  Ua input / output: 4kVrms
• clearances and creepage distances min. 8mm
• designed for DIN 35 rail mounting

• sada nejčastěji používaných pufrů 4,01 - 7,00 - 9,18 pH
• barvené provedení usnadní rozlišení při kalibraci
• 4,01 oranžový, 7,00 zelený, 9,18 modrý
• balení 100 ml PET lahve
• jmenovité hodnoty pH platí při +25°C
• roztoky jsou dodávány příslušnými certifikáty a bezpečnostními listy

Postup kalibrace najdete zde.

• stem from stainless steel diameter 5, 4 or 3mm, min. length 15mm
• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• temperature range -40…+200°C
• dielectric strength: 500V, insulation resistance min. 20MΩ (circuit to metal parts)

• two-state programmable switch for monitoring of electrical values or temperature
• output relay with changeover contact
• Possibility of easy setting of switching value by potentiometer or programmed
• supply voltage 24V DC ± 10% with galvanic separation 3kV
• DIN rail mounting
• the temperature adjusting element is inside the housing

• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• easy connecting by connector M12x1 EC-FS4-L/16
• for outdoor use, IP65, -50…+100°C

• stem from stainless steel diameter 4 or 3mm, min. length 15mm
• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, thermocouples…
• temperature range -10…+400°C
• dielectric strength: 500V, insulation resistance min. 20MΩ (circuit to metal parts)